How do I clean a silicone dab rig?

The cleaning methods for silicone Dab rigs are significantly different from those of glass dab rigs.

Solvents are not suitable for silicone as they can attack the surface.

A simple soaking is therefore not possible Silicone bongs in cleaners or solvents, as you would with glass cleaners.

There are ideal ways to clean silicone dab rigs, but also some more practical aspects that make the process easier.

In today's article, we'll go over a few tricks that have been tested and proven to be very efficient when it comes to cleaning your silicone dab rig after use.

How often should you clean your silicone dab rig?

I would advise you to clean your silicone dab rigs thoroughly every time after use.

At first glance, it may not seem as important as leaving dishes unwashed.

However, leaving them unclean for a few days and then trying to use them again will undoubtedly produce an unpleasant smell that can significantly affect your upcoming dabbing or smoking experience.

If you're cleaning glass dab rigs, check out this article: How do I clean a dab rig?

How do I clean a silicone dab rig?

Method 1: Cooking method

The boiling method is an efficient way to remove stubborn dirt from the dab rig.

Below are the detailed cleaning steps:

Step 1: Disassemble the silicone dab rig components

First, carefully separate the parts of the silicone dab rig.

Remove the stem and dab rig and set aside Glass nails or other non-silicone parts separately for later handling.

Step 2: Initial cleaning of the silicone parts

Use a soft-bristled brush and warm water mixed with a small amount of soap to perform an initial cleaning of the silicone dab rig.

This step is designed to remove dust and light dirt from the surface in preparation for subsequent deep cleaning.

Step 3: Prepare boiling water

Fill a large pot with enough water to cover, place on the stove and turn the heat to high.

Once the water is boiling, reduce the heat to a simmer to ensure the water temperature is stable and high enough to soften and loosen stubborn dirt.

Step 4: Soak Silicone Dab Rig

Wearing rubber gloves to avoid burns, carefully and slowly submerge the silicone dab rig and heat-resistant silicone parts into the boiling water.

Make sure they are completely submerged and let them sit for about 10 minutes.

During this process, you may observe a black or dark colored tar-like substance floating on the surface of the water, which is a sign that the dirt has been broken down effectively.

Step 5: Rinse the dab rig thoroughly

Remove the dab rig from the boiling water and quickly place it in the sink.

Use hot water to rinse the dab rig from all angles, especially the dab rig and downpipe, which are prone to dirt.

You can also pour clean, hot water into the dab rig and pour it down from the top to ensure that any remaining resin and dirt is thoroughly rinsed away.

Step 6: Dry naturally

Finally, dry your clean dab rig in a well-ventilated area out of direct sunlight, such as a bathroom. B. in an interior cupboard or closet.

This prevents the silicone from being damaged by heat or UV exposure and ensures that the dab rig is completely dry and ready for next use.

Method 2: Freezing method

Step 1: Disassemble and separate the parts

Carefully separate the silicone and non-silicone parts of your dab rig.

Wash non-silicone parts with warm, soapy water and set aside to dry.

Step 2: Dry the silicone parts

Make sure the silicone parts are completely dry to avoid moisture damage when frozen.

Step 3: Pack in a ziplock bag

Place the dried silicone dab rig in a sealed ziplock bag to prevent moisture from entering.

Step 4: Freeze for several hours

Place the bag in the freezer and let it sit for at least four hours or overnight. This hardens resins and residues.

Step 5: Remove and scrape off resins

Remove carefully after freezing Dab rig from the bag and the freezer.

Use a plastic scraper or blunt tool to gently chip away the hardened resins.

Step 6: Rinse and dry

Rinse the silicone dab rig with warm water to remove any residue.

Towel dry or allow to air dry before reassembling and using.

Method 3: Vinegar and Baking Soda Method

How to clean a Dab rig with vinegar and baking soda:

1. Fill the dab rig with vinegar. Use more vinegar than the amount of water you would normally have in the system.
2. Using a funnel, add 1/2 cup of baking soda to the dab rig to ensure it gets down the throat.
3. Allow the mixture to soak for at least an hour.
4. Then cover the holes with your fingers and shake the rig vigorously.
5. For particularly stubborn areas, use a cotton swab with baking soda.
6. Rinse thoroughly with warm water to remove all traces of vinegar and baking soda.
7. If you have trouble getting rid of the taste or want to slow down bacterial growth inside the plant, add lemon juice.

Diploma

By following these tips and tricks, you'll be on the right track to keeping your silicone dab rig sparkling clean.

You can enjoy smoother and more flavorful hits, taking your smoking experience to a new level.

So, dear bong enthusiasts, clean your bongs Tube with pride.

Remember that a clean Bong brings happiness, and a happy bong makes for a happy smoker.

May your hits always be smooth and your smoking sessions always blissful.